Had an old Wahl just die after probably a good 20+ years, kind of looks like the cable is frayed and splitting where it connects to the trimmer. Did a quick check online and the new products don’t even look remotely similar.
Just using it for normal hair cuts at home, any recommendations?
Edit: Preferably on the budget side.
If the cable is the only thing, you can likely open it up and replace it.
Why not fix the cable? Should be cheap and well, youre talking about BifL, well heres your chance to keep an old item running… for life.
I did this with a similarly old and heavily used Philips trimmer and it has lasted a good few years since. The Wahl ones are handy enough to take apart if memory serves so if you can I would also recommend going this route.
If you can get the casing off and post pics I’d be happy to offer advice if it’s not something you’re comfortable with.
If you have a Harbor Freight nearby grab this https://www.harborfreight.com/150-piece-terminal-and-connector-set-67683.html and a pair of crimpers for the inside electrical connections. A pair of wire strippers and you’ll be on your way.
K, my hair is crimped and full of these plastic beads, but I still need a haircut. Should I use the clippy bit of the wire strippers?
Post a pic of it? It might be fixable
First time uploading a picture here so not sure if it worked, but how does it look? I honestly have no idea how to fix it.
Inside the trimmer, it really does look more simple when you open it up. Let’s say I can just cut the wire down a bit with scissors and then strip a bit of the cable plastic. Then the points I’m uncertain on would be:
-
The rubbery fitting that surrounds the wires and secures it to the main housing. Doesn’t feel like there would be any way to yank out existing cable and thread through the unbroken part.
-
Little gold-ish pieces that pinch the wire and connect it to the screws. Look somewhat difficult to pry open.
I am located in the US but not sure which prong is which since the cable is quite twisty and the broken part is on the trimmer side.
-
Unscrew one of the wire terminals. Wrap a piece of tape around it so you know which wire is which. Unscrew the other wire. I think you should be able to pull the wire through that stress relief and then cut it off on what would be the inside instead of cutting it off outside and trying to thread it through the molded rubber. It might be stiff but you can try putting a little soap on it to lube it up. You may or may not have to split the jacket down the middle between the 2 wires depending how the relief is molded.
-
If you’re soldering, just cut the wire at the terminal ring and solder the wire right to it. You can also get new crimp on terminal rings. Take an old one to the store to match it up to get the right size.
Disclaimer: not electrician, just a DIYer that doesn’t like to spend money
Pic looks good. Probably the best option is to trim that cord a little past that break, remove the broken section, and insert the trimmed cord and reattach it to the trimmer. This will probably require soldering, and will definitely require opening the case. A picture of the trimmer with any visible screws shown will help to determine how feasible this is. You will require some solder, a soldering iron, and some flux. If you haven’t done soldering before, this could be the most forgiving project to learn it on. Electrical soldering is pretty easy, electronics are fairly precise.
The picture came thru great, and I think that’s fixable. A couple starting questions are: can the trimmer be easily opened up/ are there obvious screws keeping the housing together? Is the plug polarized? if you’re in the US this means one of the prongs of the plug is larger than the other.
Edit: i’m gonna try and find a video tutorial or something on this as I think explaining via forum post might be kinda cumbersome, but I am down to try and help you through it.
Oster Fast Feed is not a “budget” pick, but then again, few BIFL options are.
Edit: 76023-510 is the corded model.
