I have a bunch of old VHS tapes that I want to digitize. I have never digitized VHS tapes before. I picked up a generic HDMI capture card, and a generic composite to HDMI converter. Using both of those, I was planning on hooking a VCR up to a computer running OBS. Overall, I’m rather ignorant of the process. The main questions that I currently have are as follows:

  • What are the best practices for reducing the risk of damaging the tapes?
  • Are there any good steps to take to maximize video quality?
  • Is a TBC required (can it be done in software after digitization)?
  • Should I clean the VCR after every tape?
  • Should I clean every tape before digitization?
  • Should I have a separate VCR for the specific purpose of cleaning tapes?

Please let me know if you have any extra advice or recommendations at all beyond what I have mentioned. Any information at all is a big help.

You are viewing a single thread.
View all comments View context
1 point

This was very informative! Thank you for your comment!


you should check that the video output is actually at [59.94 Hz]

How does one measure the input frequency of the video feed? I’m not aware of OBS being able to monitor the frequency/refresh-rate of individual input devices, but I could certainly be wrong.


Don’t use the converter if it cannot output 480i or at the very least 480p! Scaling should happen during playback, the files should be original resolution.

I looked on Amazon again, and it seems that every converter being sold only outputs 720p, or 1080p — none of them simply repeat the input resolution, eg 480p or 480i. Would you have a converter in mind that would accomplish this?


I’d just clean the VCR after every tape if I suspect mold. You’d still need to clean the cleaning VCR after every tape to avoid cross-contamination

Do you have any resources that you would recommend for proper cleaning of a VCR?

permalink
report
parent
reply
2 points

Get an actual composite capture card for the job. HDMI converters are passable for displays and not much else, especially if they insist on scaling to HD. Most generic capture cards will output the correct, interlaced video to your PC. Check community reviews online by people who know what interlacing means. As for a question in your other comment, you then need to check that your software’s video output is interlaced and the correct resolution and frame rate. I use ffprobe (CLI) or MediaInfo (CLI/GUI) to check this.

The composite signal frequency will be either 50 Hz (SECAM or PAL) or 60000/1001 Hz (NTSC), depending on your region. Some later PAL decks have NTSC playback but you won’t see home NTSC recordings in PAL countries and vice versa unless your family moved. A good capture card driver will let you pick between these three standards and even tell you how many lines of video have been detected. However, this is not necessary as many capture cards will autodetect everything. If the resulting video is B/W, it’s probably an incorrectly set standard (NTSC and PAL encode color slightly differently (PAL is more complicated but more robust) while SECAM does its own very different thing), in which case you MUST find these settings and change them.

As for cleaning the VCR, I’d just buy a cleaning tape and “play” it for 20-30 seconds, never using the same section twice. If it’s supposed to be wet-cleaning and the isopropyl alcohol has dried up, you need to replenish it - check the attached instructions - and then give the isopropyl-cleaned mechanism a minute to dry up before inserting a videotape! Some people clean heads manually but I’m afraid I’d leave a hair or piece of cotton in the finicky mechanism and ruin everything.

permalink
report
parent
reply
1 point

Get an actual composite capture card for the job.

Ha, honestly, I wish that I would’ve done this to begin with. It’s way cheaper, and simpler to get the one composite capture card rather than converting composite to HDMI, then capturing HDMI. I’m honestly not entirely sure why I did the latter — perhaps it’s because I was under some presumption that such a device wouldn’t exist (which, now, I realize is an obviously silly assumption to make). I found this one. It’s still just a generic capture card, but it’s a direct composite capture. Do you think that it would suffice?

permalink
report
parent
reply
2 points
*

Hmmm… It seems to be an EasyCAP clone, there are several devices in this form factor with different chipsets. As far as I’ve looked, they all will stream lossless interlaced video and it’s up to you how to handle it. The “720p” claim in the listing is likely bogus - the seller just misread the actual spec, which is 720x480i for NTSC and 720x576i for PAL. The last time I was capturing video, I used the VirtualDub software, which can store the raw capture in HuffYUV, however OBS can also capture interlaced video with decent compression. This capture device seems to be labeled as “BR116” based on photos in reviews, which can help identifying the chipset. BR116 is sold by Conrad and its manual by them mentions “STK1160” in a screenshot, so this Amazon one most likely also uses the STK1160 chip, which was one of the worst ones in this timebase stability test (which means it has no TBC). However, it’s alright if your VCR is a late model that already does TBC internally.

permalink
report
parent
reply

datahoarder

!datahoarder@lemmy.ml

Create post

Who are we?

We are digital librarians. Among us are represented the various reasons to keep data – legal requirements, competitive requirements, uncertainty of permanence of cloud services, distaste for transmitting your data externally (e.g. government or corporate espionage), cultural and familial archivists, internet collapse preppers, and people who do it themselves so they’re sure it’s done right. Everyone has their reasons for curating the data they have decided to keep (either forever or For A Damn Long Time). Along the way we have sought out like-minded individuals to exchange strategies, war stories, and cautionary tales of failures.

We are one. We are legion. And we’re trying really hard not to forget.

– 5-4-3-2-1-bang from this thread

Community stats

  • 395

    Monthly active users

  • 108

    Posts

  • 534

    Comments

Community moderators